Cover is vented to match intake polished stainless cover.
Measures 9 3/4” x 4”. Includes hardware.
Engine Fuse Box Polished Stainless Cover
Includes matching chrome cap that attaches to locking knob on top of original lid.
Battery Stainless Cover
Designed to fit original AC Delco batteries used by GM in 1997-2000. Has protective
black molding around outer lip to secure battery in place.
Battery Polished Stainless Cover
Has protective black molding around outer lip to secure battery in place.
Intake Polished Stainless Cover
Easy to install.
Fuel Rail Polished Stainless Covers (pair)
Covers follow pattern of original plastic fuel rails covers. Nothing to cut or remove.
Simply attach over factory fuel rail covers with supplied velcro.
Rear Deck Emblem on Hatch
Inner Fender Polished Stainless Covers
Contoured to fit with supplied velcro. Allows you to remove if necessary to see decals
on each inner fender.
Cowl Polished Stainless Vent Covers (2pcs)
2 piece design to lay over black plastic cowl vent area. One side has vent cutouts
to match up to factory vents found on original black plastic cowl section. Main portion
on drivers side laps over other half where they join in center.
Front Cover Polished Stainless Insert Panel
Covers exposed lip of header panel.
Upper Radiator Support Polished Stainless
2 piece design that simply snaps into place over factory upper radiator support.
Each slips in so it cover exposed top surface of plastic radiator support. Each side
measures 6.5” x 16”. Rib design in top surface adds to appearance
97-04 Hood Shock Chrome Covers (2pcs)
Made of brass. Each tube is hand polished and chrome plated.
Triple Chrome Plated Hood Latches (pair)
Hood strikers are triped chrome plated. Comes with 4 new stainless washers and 4
Headlight Motor Chrome Covers
Fits C5 Corvettes. Simply slip rubber boot off to install new chrome covers. Designed
to be installed without having to unbolt headlight motors from car.
Brake Booster Polished Stainless Cover
Attaches to top portion of brake booster. Is curved cover that covers top portion
of brake booster behind brake reservoir.
Brake Reservoir Polished Stainless Cover
Covers top and also extends down exposed side of brake reservoir. Cover is slotted.
Measures 3.5” x 6.75” x 5”. Easy to install.
Power Steering Reservoir Housing
Polished Stainless Cover
Covers top surface and visible side facing drivers side fender of housing. Measures
2.25” x 3.5” x5”. Easy to install.
Accent Chrome Covers for Oil, PS, PB & Radiator Cap (set of 4)
Designed to slip over factory oil, power steering, brake and radiator caps. Simply
accents original caps, allowing wording on to be shown.
Windshield Washer Reservoir Cap
Made of copper and chrome plated. Measures 2.25” in diameter.
Air Conditioning Check Valve
Chrome Cap Covers (2pcs)
Located on passenger side in engine compartment. Each main has capped valve (fill
point) that has black plastic cap on valve opening.
Hood Hinge Bolt Chrome Cap Covers (4pcs)
Designed to slip over 2 bolt heads that secure hinge assembly to either side of hood.
Made of copper and chrome plated for lasting quality.
Front Nose Lip Chrome Cap Covers (6pcs)
Kit consists of 6 metal chrome-plated copper caps. Simply slips over 6 factory slips
that are visible on inner lip when hood is in open position.
Trunk Hinge Bolt Chrome Covers (8pcs)
Designed to slip over 8 bolt heads that secure trunk hinge assembly at both end.
End that secures the hinge assembly to trunk lid and end that secures hinge assembly
to car body.
Underhood Light Polished Stainless
Gives underhood nice finishing ouch to compliment. Simply slips around factory hood
light giving it a nice, bright, polished stainless edge around light.
Engine Compartment Polished Stainless
Detail Screw Kit (25pcs)
Each screw and washer is hand polished to a high luster. They replace factory Torx
head screws that secure the inner fender to each outer fender, plus 4 screws are
used on each headlight shell.
Door Jam Chrome Detail Screw Set (6pcs)
Kit covers the 3 screws located in each door jam area of all C5 Corvettes.